Pipe Cleaning Quote Comparison

Match the work scope. Compare actual costs, conditional caps and balances in KRW.

Actual tax-inclusive quotes · KRW

Define the same pipe system and work

Compare one system at a time. Confirm cold-water and hot-water coverage separately. Changing systems clears quantities with different units and confirmation checks.

Related calculators

Compare pipe-cleaning quotes for the same work

A headline cleaning price can cover fewer heating circuits, omit connection and restoration, or leave post-work checks unpriced.
Water-supply quotes may also cover different cold-water outlets and domestic hot-water lines.
This calculator helps households, shop operators and building managers compare two written quotes before ordering the work.

Use the same system, quantity and handover scope for both providers, then distinguish known charges, missing work, conditional extra-charge caps and the balance after an advance payment.
The next action is to send the unanswered scope and billing questions to each provider and obtain a revised quote.
This is a Korea-related 2026 planning worksheet using actual tax-inclusive Korean won (KRW), with no built-in market price or tax rate.

Choosing between clearing and replacement?

This page compares providers for an agreed cleaning job.
Use the drain-pipe clearing and replacement cost calculator to compare repeated clearing with partial or full replacement over three years.
Neither tool diagnoses the site or selects a suitable cleaning method.

Define the system and the start and end of the job

Water supply: outlet count

Enter the number of outlets the provider has confirmed as cleaning targets.
Record whether the scope covers cold water, domestic hot water, or a clearly itemized combination.
Counting visible taps alone does not establish that every pipe downstream of the meter is included.

Heating: circuit count

Use the actual circuits to be serviced at the manifold, rather than assuming one circuit per room.
Confirm accessible connections, valve condition and any excluded circuits.
Domestic hot-water supply and circulating heating water are separate scopes.

Drainage: length in metres

Enter a confirmed length between defined endpoints, with up to two decimal places.
An internal branch and a shared vertical drain are different scopes even if the quoted lengths match.
Ask for measurement or provider confirmation before treating an unknown length as established.

One system per comparison

Outlets, circuits and metres cannot be added together.
For a bundle, obtain the system-specific scope and allocation before comparing each system separately.
When changing the system, recheck all quantities and each provider’s target and permitted-method confirmation.

Separate required, quoted and included quantities

The required quantity describes the whole job you need.
The quoted quantity is the work the provider agrees to perform, while the included quantity is the amount covered by its base price.
A quote for three circuits does not cover a five-circuit job simply because its price is lower.
The calculator identifies the shortage and withholds a qualified price ranking.

Base charge and minimum billing

  • Quantity shortage = max(0, required quantity − quoted quantity)
  • Excess quantity = max(0, quoted quantity − included quantity)
  • Base charge = max(base price + rounded KRW(excess quantity × extra-unit price), minimum charge)

The minimum applies to the base price plus excess-quantity charge, before separately priced tasks are added.
If a provider’s minimum instead covers all extras, obtain a breakdown compatible with this structure rather than moving the same charge between fields arbitrarily.
Unused included quantity never produces a negative charge or an automatic refund.

Enter every amount on the same tax-inclusive KRW basis.
A supply-price-only quote must first be clarified with the provider because the tool does not add a tax rate automatically.
Do not enter connection, parts or restoration again if those costs are already included in the base charge.

Check finishing work and the status of each charge

Beyond cleaning, confirm access and connection/disconnection/restoration, rinsing, resupply or restart and post-work checks, and parts or handling.
The required handover differs by system, so describe what the provider actually undertakes.
Select included only when the entire stated task is confirmed within the base price.

Included or a fixed extra

Included means no additional charge for that scope.
A fixed extra is payable in the completed-job scenario.
An explicitly confirmed zero is valid, but a blank or unanswered question is not a free service.

Conditional cap or unknown

A conditional cap represents an additional amount between zero and the confirmed maximum if its condition occurs.
A charge that definitely applies belongs under fixed extras instead.
An excluded, unpriced or unconfirmed task prevents a finite overall upper total.

Post-work checks record contractual scope; they do not certify drinking-water safety or equipment performance.
Obtain confirmation from the provider and the relevant manufacturer that the method is permitted for the actual product, materials and connections.
A confirmation checkbox is your record and does not validate pressure settings, cleaning chemicals or the need for cleaning.

Completed work and an incomplete job are alternatives

Completed-job range

The known subtotal combines a known base charge with fixed task and revisit charges.
Conditional extras stay outside that subtotal and are added only to the upper total.
When every charge is established, the completed-job range runs from the known subtotal to that subtotal plus the conditional caps.
Known extras remain visible if the base charge is missing, but that partial subtotal is not a complete quote or a basis for selecting the cheapest provider.

Incomplete-job charge

The incomplete-job charge applies to a different outcome; it is not added to the completed-job price.
Ask which situations, such as an inaccessible connection or work stopped on site, trigger the quoted amount.
Enter revisit costs in the completed-job comparison only when they are additional charges in that scenario.
Do not add an incomplete-job fee twice through a revisit field.

An unconfirmed incomplete-job rule keeps the provider ranking on hold even when the completed-job costs are entered.
The tool does not assume free revisits or no charge for an incomplete visit.
Where a later visit replaces or credits the first charge, ask for the net amount in each outcome before using this simple comparison.

Worked example: five heating circuits

These fictional amounts test the arithmetic and are not market prices or recommended charges.
Assume both providers cover all five heating circuits and the target and permitted method are confirmed.
All figures include tax and are in KRW.

Fictional provider A and B charges for five heating circuits
MeasureProvider AProvider B
Base price200,000 KRW330,000 KRW
Included circuits35
Extra-circuit price30,000 KRWNot applied / unquoted
Minimum charge250,000 KRW0 KRW
Calculated base charge260,000 KRW330,000 KRW
Fixed connection/restoration40,000 KRWIncluded
Rinsing, restart checks, parts/handlingIncludedIncluded
Additional revisit charge0–50,000 KRW0 KRW
Completed-job total300,000–350,000 KRW330,000 KRW
Alternative incomplete-job charge50,000 KRW0 KRW
Already paid100,000 KRW100,000 KRW
Completed-job balance200,000–250,000 KRW230,000 KRW

A has two excess circuits at 30,000 KRW each, making 260,000 KRW before the separately priced restoration.
That is above the 250,000 KRW minimum, so the calculated base remains 260,000 KRW.
Adding 40,000 KRW gives a known subtotal of 300,000 KRW and the revisit cap raises the upper total to 350,000 KRW.
B’s 330,000 KRW lies inside A’s range, so neither is confirmed cheaper.
Subtracting advances changes the balances, not the overall quote ranking.

Interpret overlapping ranges and balances

A is confirmed lower only when its completed-job upper total is below B’s fully established lower total.
Two equal fixed totals are a tie; ranges that overlap or merely touch do not establish a strict price advantage.
Missing charges, a quantity shortage or an unconfirmed target or method prevents qualified ranking.
A provider with unanswered fields is not promoted because its partial subtotal happens to look smaller.

A negative balance is not an automatic refund

The balance is the completed-job amount or upper total minus the amount already paid.
A negative number means the advance exceeds the charge under that entered scenario.
It does not determine a legal right to repayment or an automatic refundable amount.
Confirm the actual cancellation, incomplete-job and revisit agreement before settling with the provider.
If the advance is unknown, leave the balance unresolved even if the total quote can be compared.

From the quote to a specific revision request

  1. Collect site photographs and system information, then confirm the endpoints and required quantity.
    Identify cold-water supply, hot-water supply, heating and drainage separately.
  2. Enter A’s base price, full quoted quantity, included quantity, extra-unit price and minimum.
    For a package quote, check that included work is not entered again as an extra.
  3. Record the four finishing tasks and revisit charge as included, fixed, capped or unresolved, then confirm the incomplete-job rule.
    Do not use zero as a substitute for an unanswered question.
  4. Apply the same scope and tax-inclusive basis to B, then read the shortages and unresolved questions before comparing amounts.
    Replace any fictional example values with your actual written quote.
  5. Save the comparison and question list, ask each provider for the missing scope and charge conditions in writing, and edit the relevant quote after receiving a revision.

Contract checks for common situations

Several heating circuits

List the circuits to be cleaned and whether they can actually be connected.
Ask what happens if a valve or connection prevents completion, including any replacement-part charge.
The tool does not impose an automatic percentage surcharge for having more circuits.

Cold-water and hot-water bundles

Confirm the endpoints and outlet coverage for each system even when the product has one name.
Do not recombine unit prices between providers if the bundle allocation is not established.
Record dismantling, reassembly, restoration and handover checks.

A difficult-to-access shop

Check meter or manifold access, work outside trading hours, moving items and protection of surrounding surfaces.
Record a confirmed extra or actual cap only where those costs are separately chargeable.
Keep the same cost out of the base price and extra field at the same time.

Returning after incomplete work

Ask whether the first charge is credited, whether the same problem qualifies for a free revisit, and who supplies parts.
If the agreement cannot be separated into a completed-job extra and an alternative incomplete-job charge, obtain a revised quote showing the net charge for each outcome.

Frequently asked questions

Does this show the average pipe-cleaning price?

No; it calculates actual tax-inclusive quotes entered by you, and all worked-example prices are fictional.

Why are included and quoted quantities separate?

Included quantity sets the base-price allowance, while quoted quantity establishes the work the provider agrees to do, so a shortage cannot be mistaken for a cheaper equivalent quote.

Can I replace a blank with zero?

Enter zero only for an explicitly confirmed free or no-extra-charge item, and leave unanswered prices or scope unconfirmed.

Does the minimum include parts and restoration?

This model applies the minimum to base plus excess-quantity charges before extras, so obtain a compatible breakdown if the provider uses a different minimum rule.

Is the incomplete-job fee added to the completed price?

No; incomplete and completed work are alternative scenarios and their charges are not added together.

Can I select the provider with the lower upper total?

Only confirmed scope, quantities, permitted method and billing conditions support ranking, and overlapping ranges do not establish a definite cheaper provider.

Is a negative balance a refund?

It only shows that the advance exceeds the entered scenario’s charge, and the actual repayment position requires separate agreement and settlement checks.

Does this predict water safety or heating performance?

No; the tool provides billing arithmetic and does not assess cleaning necessity, water safety, effectiveness, energy savings or construction suitability.

Sources and update basis

The project reference year is 2026 and the public materials were checked on 20 November 2026 (2026-11-20).
This worksheet applies no statutory tariff or service obligation; obtain every price and billing condition from the actual contract.

Provider material does not establish a universal price or the included scope of every provider.
It does not establish rinsing charges, incomplete-job billing or revisit caps for your contract.
Recheck written terms and the actual product manual for every order, and review public service descriptions quarterly.

Turn missing details into a revised quote

First confirm that both providers cover the same pipe section and finishing work.
Return to the calculator, enter your written quotes, and collect quantity shortages, unanswered tasks and extra-charge limits.
A comparison showing completed and incomplete outcomes alongside advances makes the final pre-contract questions specific.