Conveyor Bottleneck Throughput and Payback Calculator

Compare up to four improvements using belt speed, product pitch, station capacities and monthly demand. Review throughput, net monthly benefit and simple payback in KRW.

Current conveyor line

Shared comparison assumptions

Single-lane serial-line steady-state model · all money in KRW · sources checked 2026-11-22. Dorner 3200 Common Drive, p5 · Nercon Accumulation Article · IISE Bottlenecks · US DOE/PNNL Cost Effectiveness, section 5.1.2

Related calculators

Separate conveyor speed from saleable output

A faster conveyor may leave shipments unchanged when a packing or inspection station remains the limiting process.
Even a genuine capacity increase has no additional sales value if demand cannot absorb it.
This calculator compares your current line with up to four improvement options, using product pitch, measured process rates, line efficiency, monthly demand and confirmed costs.
It supports small manufacturing and material handling operators who need to discuss a quotation and load test before committing capital.

Start with throughput

Identify the smallest of belt capacity and the upstream and downstream process limits.
Apply line efficiency and monthly hours, then cap realizable output at monthly demand.

Then evaluate cash

Value additional realizable output at its contribution margin, add cash labor savings and subtract incremental operating and maintenance costs.
Divide confirmed initial spending by positive monthly net benefit to estimate simple payback.

This is a steady-state model of a single-file serial transfer line.
It does not calculate AS/RS storage positions, cranes or shuttles, and does not establish safe equipment design or guarantee performance.
Both language versions use the same calculations and KRW cash amounts; English does not switch the model to USD or apply foreign tax rules.

Inputs to take from the measurement sheet

Belt speed and product pitch

Enter actual belt speed in m/min.
Pitch in m/piece is the product length in the direction of travel plus the gap to the next product.
A 0.3 m product followed by a 0.2 m gap has a 0.5 m pitch; using the gap alone would overstate capacity.
For multiple lanes or merging flows, first agree on a consistent piece-based measurement with the supplier rather than treating this single-file model as a layout simulator.

Measured upstream and downstream rates

Use pieces/h measured while the process is running.
If there are several upstream stations, enter the lowest measured rate in that section; do the same for the downstream section.
Do not add serial station rates or multiply a nominal rate by the number of stations.
Keep product mix, test load and measurement conditions comparable between the existing line and each option.

Whole-line efficiency and monthly conditions

Line efficiency is your verified adjustment for stoppages, starvation, blocking and other losses affecting the line as a whole.
The calculator does not infer it from one motor or an average of machine uptime percentages.
If your measured rate already includes downtime, review it with efficiency set to 100% to avoid deducting the same loss twice.
Monthly operating hours are common to all options, with a maximum of 744 hours; monthly demand is a whole number of pieces that can actually be processed or sold in the same month.

Blank is different from confirmed zero

Leave an unknown amount blank or mark its status unknown.
Enter 0 only when you have confirmed that no charge applies.
Zero speed, process rate, efficiency or demand is a valid zero-capacity or zero-output case, while zero pitch is invalid because the formula divides by pitch.
Negative values, values outside the field limits and fractional monthly demand also require correction.

Compare options in three steps

  1. Enter the current line and common assumptions. Speed and pitch allow a partial belt-capacity result before all other fields are complete.
    Add process limits, line efficiency, monthly hours, demand, contribution margin, target payback months and demand sensitivity.
  2. Complete up to four improvement options. Enter each line configuration, quotation scope, labor cash realization and incremental operating and maintenance amounts.
    Switching options or steps preserves the entered values so that you can check competing supplier quotations.
  3. Read matching measures side by side. Start with monthly net benefit, payback, bottleneck and realizable output, then inspect the target additional volume and outstanding items.
    Save or print the comparison and use it to agree on a load test and complete cost scope.

A partially completed form distinguishes calculable capacity and known cost subtotals from unresolved economics.
Do not treat a confirmed subtotal as the full project price.
The worked example has a visible example state, and restoring your work returns to your saved inputs, step and active option.
On a phone, use the result view’s edit action to return to the inputs and review the same measures after changing a value.

Throughput and simple payback formulas

Theoretical belt capacity

60 × speed (m/min) ÷ pitch (m/piece) = pieces/h

Bottleneck and effective rate

Bottleneck = min(belt, upstream, downstream); effective rate = bottleneck × efficiency / 100

Monthly capacity and served output

Capacity = effective rate × monthly hours; served output = min(capacity, monthly demand)

Monthly net benefit

(Proposed served output − current served output) × contribution margin + labor savings − incremental operation − incremental maintenance

Cash labor savings

Hours saved × hourly labor cost × cash realization / 100

Simple payback in months

Confirmed initial investment ÷ positive monthly net benefit

Tied minimum rates identify multiple bottlenecks.
An option that reduces served output retains a negative volume difference, so lost contribution reduces net benefit.
Only count labor savings that reduce cash spending, such as avoided overtime, outsourcing or hiring; reassigned time does not automatically become cash savings.
Saved hours use a one-person-equivalent model and cannot exceed the common monthly hours; summed hours from several workers are outside this model.
If the contribution margin already includes the same labor reduction, set separate labor savings to zero to avoid double counting.

A positive investment with zero or negative monthly net benefit has no payback under these assumptions.
Zero investment with nonnegative benefit is shown as a zero-month, no-investment case; zero investment with negative benefit is still not a payback case.
Calculations retain intermediate precision; displayed KRW amounts round to whole won, throughput uses up to two decimal places and payback uses one decimal place.

Quotation scope, tax and confirmed spending

Start with the equipment package, then record installation, controls integration and other costs as included, separate or unknown.
Included items are not added again even if a separate amount was previously entered.
Only separate confirmed charges increase initial investment.
Unresolved required costs leave a known subtotal and a list of missing items, while final investment, net benefit and payback comparison remain pending.

Use the supplier’s confirmed tax amount

Choose included, separate or unknown tax status; for separate tax, enter the actual contractual amount in KRW.
The calculator does not impose a blanket 10% VAT rate or decide exemption status.
Entered tax is part of cash spending, with no automatic removal for input tax credits or refunds.
This cash comparison therefore differs from a complete after-tax investment analysis.

Check quotation dates

Enter actual calendar dates for the quotation, validity end and implementation.
Economic comparison requires quotation date ≤ implementation date ≤ validity end.
Missing, reversed or out-of-period dates leave capacity and confirmed subtotals available while you obtain an applicable quotation.
This checks the price period rather than determining the legal enforceability of a contract.

Worked example: improve the downstream limit

Assume a current speed of 10 m/min, pitch of 0.5 m/piece, upstream rate of 1,500 pieces/h, downstream rate of 1,000 pieces/h, efficiency of 80%, 160 operating hours and demand of 200,000 pieces/month.
Contribution margin is KRW 50 per additional piece and target payback is 24 months.
These are calculation examples, not market prices.
Option A uses 15 m/min, the same pitch, 1,600 pieces/h upstream, 1,400 pieces/h downstream and the same efficiency.

Throughput calculation for the current line and option A
MeasureCurrentOption A
Belt capacity (pieces/h)1,2001,800
Downstream bottleneck (pieces/h)1,0001,400
Effective rate (pieces/h)8001,120
Monthly capacity (pieces)128,000179,200
Demand-capped served output (pieces)128,000179,200

KRW 24,200,000 investment and KRW 2,610,000 monthly net benefit

Add KRW 20,000,000 for the package, KRW 2,000,000 separate installation and KRW 2,200,000 confirmed separate tax.
Controls are included and separate other costs are confirmed at zero, giving KRW 24,200,000 initial investment.
Additional volume is 51,200 pieces × KRW 50 = KRW 2,560,000 contribution.
Labor savings are 20 hours × KRW 20,000 × 50% cash realization = KRW 200,000.
Subtract KRW 100,000 operation and KRW 50,000 maintenance to obtain KRW 2,610,000 monthly net benefit.
Payback is 9.2720306513… months, displayed as 9.3 months.

If option B increases belt speed but leaves the downstream rate at 1,000 pieces/h, added volume is zero.
The same labor and operating assumptions leave only KRW 50,000 monthly benefit and a 484-month payback.
At demand of 100,000 pieces, both the current line and option A serve 100,000, also producing a 484-month payback.
With contribution margin and labor savings both zero, net benefit is −KRW 150,000 and payback is unavailable.

Break-even volume, target volume and conditional hours

Additional volume for operating break-even

Use max(0, (incremental operation + incremental maintenance − cash labor savings) / contribution margin).
This covers recurring monthly costs, separately from recovery of initial investment.
The example requires zero additional pieces for operating break-even because labor savings exceed incremental recurring costs.

Additional volume for target payback

Use max(0, (investment / target months + incremental operation + incremental maintenance − labor savings) / contribution margin).
The example’s 24-month target requires 19,166.6667… additional pieces, displayed with upward whole-piece rounding as 19,167.
Distinguish unused demand, proposed capacity headroom and actual realizable additional output; a target above realizable headroom is unmet under the current plan.
At zero margin, the volume target is unattainable if a positive cash requirement remains, or zero if labor savings already cover it.

Conditional operating hours

Required hours = precise target additional volume / (proposed effective rate − current effective rate).
The example gives 59.8958333… hours, conditional on both lines remaining below their demand caps.
This rearrangement holds entered monthly labor savings and incremental operation and maintenance costs fixed; it does not automatically scale them with hours.
If the effective rate does not increase or demand constrains output, this is not an achievable operating schedule.
To evaluate another schedule, edit the common monthly hours and the corresponding labor and cost assumptions, then recalculate served output and net benefit.

Keep full precision for economic boundaries and use upward rounding only for displayed required piece counts.
For an option that loses output, inspect actual net benefit and whether payback meets the target rather than relying on a required-volume label alone.

Demand sensitivity and practical uses

Sensitivity changes only monthly demand by your selected ±percentage and recalculates current and proposed served output.
It holds labor savings, investment and process settings constant; it is an assumption check rather than a sales forecast or an all-risk scenario.
At ±10% of the example’s 200,000 pieces, demand is 180,000 and 220,000.
Option A’s capacity of 179,200 is below both, so additional output stays at 51,200 and monthly benefit at KRW 2,610,000.
An unchanged result under lower demand means capacity is still the tighter limit in that range.

  • Discuss a packing upgrade: compare a belt-only option with an option that also removes the packing limit and request an equivalent load test.
  • Test uncertain orders: enter confirmed orders and an optimistic sales plan as different demand assumptions to see when extra capacity turns into contribution.
  • Review a labor-led investment: distinguish redeployment from cash reductions and test a lower cash realization percentage.
  • Compare suppliers: align installation, controls, tax and quotation validity across up to four options before comparing the financial measures.

Limits of the model

The minimum-rate model with a whole-line efficiency adjustment simplifies steady-state operation.
It does not dynamically simulate accumulation and clearing, random stoppages, merges, branches, mixed products, rejects, acceleration, slippage or product damage.
Verify the assumptions with the supplier using actual products, load and shift conditions in a sufficiently long test.

Monthly benefit assumes the same normal month repeats after installation is complete.
Installation disruption, ramp-up, financing, discounting, tax incentives, major replacements, residual value and post-payback cash flows are excluded.
This is not NPV or IRR, a universal acceptable payback threshold or an automatic recommendation of the best option.
The result does not certify load capacity, guarding, permits or other engineering and safety suitability.

Frequently asked questions

Does doubling belt speed double production?

Not if an upstream process, downstream process or demand is the tighter limit.
Read the bottleneck and demand-capped served output together.

What if I only have an average rate including downtime?

Review that rate with efficiency at 100% to avoid deducting the same loss twice.
Ask the supplier to distinguish running rates from whole-line efficiency.

Can I value every saved labor hour as a benefit?

Use only the share that reduces cash spending.
Avoid counting labor already included in contribution margin and do not sum several workers’ hours in this one-person-equivalent model.

Why is payback pending when I have entered some prices?

Some required scope, tax or quotation dates remain unconfirmed.
Review the known subtotal and capacity, then complete the outstanding items before comparing investment and payback.

Is a zero contribution margin allowed?

A confirmed zero is valid and makes the volume contribution zero.
A positive remaining target cash requirement cannot be covered by additional pieces at zero margin.

Do the required hours guarantee target payback?

No.
They are conditional on both lines staying below demand caps.
Edit common hours and recalculate output and benefit while verifying real demand and cash savings.

Primary sources and the next update

Sources reviewed on November 22, 2026 (2026-11-22).
These manufacturer and professional references support the unit relationship, bottleneck interpretation and simple payback method; their product limits are not adopted as universal design values or Korean statutory prices.

Recheck product pitch, running versus average measurement definitions, line efficiency, demand, cash labor realization, included scope, tax amounts and quotation dates when updating the comparison.
No statutory tax rate or safety standard is automatically applied.

Take the comparison to the load-test discussion

Begin with the current belt speed and product pitch, then add measured bottleneck records.
Save or print the bottleneck, incremental benefit and confirmation checklist to align test volume, duration and included costs with the supplier.
Resolve missing items before using the comparison to decide investment and order scope.